dowel pin 定位梢
draft 拔模锥度
draw bead张力调整杆
drive bearing传动轴承
ejection pad顶出衬垫
ejector脱模器
ejector guide pin顶出导梢
ejector leader busher顶出导梢衬套
ejector pad顶出垫
ejector pin顶出梢
ejector plate顶出板
ejector rod顶出杆
ejector sleeve顶出衬套
ejector valve顶出阀
eye bolt环首螺栓
filling core椿入蕊
film gate薄膜形浇口
finger pin指形梢
finish machined plate角形模板
finish machined round plate圆形模板
fixed bolster plate固定侧模板
flanged pin带凸缘销
flash gate毛边形浇口
flask上箱
floating punch浮动冲头
gate浇口
gate land浇口面
gib凹形拉紧楔
goose neck鹅颈管
guide bushing引导衬套
guide pin导梢
guide post引导柱
guide plate导板
guide rail导轨
head punch顶头冲孔
headless punch直柄冲头
heavily tapered solid整体模蕊盒
hose nippler管接头
impact damper缓冲器
injection ram压射柱塞
inlay busher嵌入衬套
inner plunger内柱塞
inner punch内冲头
insert嵌件
insert pin嵌件梢
一、入水：gate
进入位： gate location
水口形式：gate type
大水口：edge gate
细水口： pin-point gate
水口大小：gate size
转水口： switching runner/gate
唧嘴口径： sprue diameter
二、流道: runner
热流道： hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner）
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴： hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头： connector plug
插座： connector socket
密封/封料： seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件： mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板： suPPOrt plate
螺丝： screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针： ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
行位（滑块）： slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
机械前沿微信号：jixieqianyan
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆：early return bar
气阀：valves
斜导边：angle pin
术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
铜公(电极）：copper electrode
dowel pin定位梢
draft拔模锥度
draw bead张力调整杆
drive bearing传动轴承
ejection pad顶出衬垫
ejector脱模器
ejector guide pin顶出导梢
ejector leader busher顶出导梢衬套
ejector pad顶出垫
ejector pin顶出梢
ejector plate顶出板
ejector rod顶出杆
ejector sleeve顶出衬套
ejector valve顶出阀
eye bolt环首螺栓
filling core椿入蕊
film gate薄膜形浇口
finger pin指形梢
finish machined plate角形模板
finish machined round plate圆形模板
fixed bolster plate固定侧模板
flanged pin带凸缘销
flash gate毛边形浇口
flask上箱
floating punch浮动冲头
gate浇口
gate land浇口面
gib凹形拉紧楔
goose neck鹅颈管
guide bushing引导衬套
guide pin导梢
guide post引导柱
guide plate导板
guide rail导轨
head punch顶头冲孔
headless punch直柄冲头
heavily tapered solid整体模蕊盒
hose nippler管接头
impact damper缓冲器
injection ram压射柱塞
inlay busher嵌入衬套
inner plunger内柱塞
inner punch内冲头
insert嵌件
insert pin嵌件梢
king pin转向梢
king pin bush主梢
difference quantity差异量
cause analysis原因分析
raw materials原料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板
bushing block衬套
insert 入块club car高尔夫球车
capability能力
Is these useful for you? follow JC tooling, let's learn together!
